LWANNIER90 issue with KPOINTS file

[cantele]

Dear all,

I cannot figure out what's wrong with my input files in trying to setup a wannier90 calculation.

I have an hexagonal lattice and tried with several KPOINTS files. Just as an example:

Automatic mesh
0
A
9

but I also tried for example 8x8x8, 8x8x2 and other grids.

If the option LWANNIER90=.TRUE. is disabled in the INCAR file, everything works fine. However, with that option
I always get in the output the error message

internal error in GENERATE_KPOINTS_TRANS: G vector not found 4 0 0 -1 0 0 1 1 mkpoints_change.F

and many others similar lines.

Can anyone help me in finding where is the issue?

Thanks,

Giovanni

[admin]

Have a look at:
http://cms.mpi.univie.ac.at/vasp-forum/ ... ER*#p14821

[cantele]

Hi,

thanks for reply.

It seems that ISYM=-1 changes thinks, in that the job start running with no k-point error. However, while with LWANNIER90 unset the run
terminates after very few minutes, in this case the job seems to be stalled at "DAV: 12 " self-consistency step.
Removing NPAR, as specified in another reply of the topic you suggested, leads to a "forrtl: No such file or directory" error after
"DAV: 13" step.

I cannot figure out why the code behaves abnormally with LWANNIER90=.TRUE. Indeed, the only difference with LWANNIER90=.FALSE.
is that the full k-point list should be used, so it should just take some more time to reach self-consistency.

Giovanni

[cantele]

Just to more remarks:

i) I tried different combinations of NPAR, number of CPUs, number of CPUs per node and got in some cases different failure results. Examples:

• Once arrived at some DAV step (12th in my case) VASP hangs there, and keeps running without doing anything
• or, VASP stops with the error:
  

  forrtl: severe (29): file not found, unit 99, file /scratch/cantele/MoS2_crystal_w90/wannier90.win

• or, VASP start claiming about

  WARNING: Sub-Space-Matrix is not hermitian in DAV

  and then stops with

  forrtl: severe (174): SIGSEGV, segmentation fault occurred

All the above issues seem to indicate something strange in parallel runs.


ii) The only run that I was able to correctly terminate is with just 1 CPU. However, after the end of the run, I find the wannier90.win, wannier90.wout, the wannier90.eig and the wannier90.mmn files BUT NOT the wannier90.amn so the subsequent wannier90.x run claims about missing amn file. How can it happen that only two of the three needed files (eig, mmn, amn) are written in output? I also tried to set LWRITE_MMN_AMN = .TRUE. with no success (that variable is by default set to true if lwannier90=.true.). Can anyone help me on this point?

[admin]

i) Looks like parallel version is not correctly compiled.
ii) wannier90.win created upon setting LWANNIER90=.TRUE. does not include any projection.
If some projection block is speciefied prior to the first vasp run, corresponding projections of the Bloch functions
are written into wannier90.amn .
For details how to specify projections cf. http://www.wannier.org/user_guide.html ,
or wannier-forum at http://www.wannier.org/forum.html

[cantele]

Hi,

thanks for reply. OK, I solved issue ii) (sorry, I didn't realize that my own wannier90.win is mandatory if the man file is required!), but I'm still stuck with issue i).

Is it possible that the parallel version is not correctly compiled if I find that error ONLY when LWANNIER90=.true. ? Do you have any idea of how to check
if there is something wrong with my executable?

I quote below the Makefile I used. I'm currently using ifort 12.1.4 20120410 and Open MPI 1.6

.SUFFIXES: .inc .f .f90 .F
#-----------------------------------------------------------------------
# Makefile for Intel Fortran compiler for Pentium/Athlon/Opteron
# based systems
# we recommend this makefile for both Intel as well as AMD systems
# for AMD based systems appropriate BLAS (libgoto) and fftw libraries are
# however mandatory (whereas they are optional for Intel platforms)
# For Athlon we recommend
# ) to link against libgoto (and mkl as a backup for missing routines)
# ) odd enough link in libfftw3xf_intel.a (fftw interface for mkl)
# feedback is greatly appreciated
#
# The makefile was tested only under Linux on Intel and AMD platforms
# the following compiler versions have been tested:
# - ifc.7.1 works stable somewhat slow but reliably
# - ifc.8.1 fails to compile the code properly
# - ifc.9.1 recommended (both for 32 and 64 bit)
# - ifc.10.1 partially recommended (both for 32 and 64 bit)
# tested build 20080312 Package ID: l_fc_p_10.1.015
# the gamma only mpi version can not be compiles
# using ifc.10.1
# - ifc.11.1 partially recommended (some problems with Gamma only and intel fftw)
# Build 20090630 Package ID: l_cprof_p_11.1.046
# - ifort.12.1 strongly recommended (we use this to compile vasp)
# Version 12.1.5.339 Build 20120612
#
# it might be required to change some of library path ways, since
# LINUX installations vary a lot
#
# Hence check ***ALL*** options in this makefile very carefully
#-----------------------------------------------------------------------
#
# BLAS must be installed on the machine
# there are several options:
# 1) very slow but works:
# retrieve the lapackage from ftp.netlib.org
# and compile the blas routines (BLAS/SRC directory)
# please use g77 or f77 for the compilation. When I tried to
# use pgf77 or pgf90 for BLAS, VASP hang up when calling
# ZHEEV (however this was with lapack 1.1 now I use lapack 2.0)
# 2) more desirable: get an optimized BLAS
#
# the two most reliable packages around are presently:
# 2a) Intels own optimised BLAS (PIII, P4, PD, PC2, Itanium)
# http://developer.intel.com/software/products/mkl/
# this is really excellent, if you use Intel CPU's
#
# 2b) probably fastest SSE2 (4 GFlops on P4, 2.53 GHz, 16 GFlops PD,
# around 30 GFlops on Quad core)
# Kazushige Goto's BLAS
# http://www.cs.utexas.edu/users/kgoto/signup_first.html
# http://www.tacc.utexas.edu/resources/software/
#
#-----------------------------------------------------------------------

# all CPP processed fortran files have the extension .f90
SUFFIX=.f90

#-----------------------------------------------------------------------
# fortran compiler and linker
#-----------------------------------------------------------------------
FC=ifort
# fortran linker
FCL=$(FC)


#-----------------------------------------------------------------------
# whereis CPP ?? (I need CPP, can't use gcc with proper options)
# that's the location of gcc for SUSE 5.3
#
# CPP_ = /usr/lib/gcc-lib/i486-linux/2.7.2/cpp -P -C
#
# that's probably the right line for some Red Hat distribution:
#
# CPP_ = /usr/lib/gcc-lib/i386-redhat-linux/2.7.2.3/cpp -P -C
#
# SUSE X.X, maybe some Red Hat distributions:

CPP_ = ./preprocess <$*.F | /usr/bin/cpp -P -C -traditional >$*$(SUFFIX)

# this release should be fpp clean
# we now recommend fpp as preprocessor
# if this fails go back to cpp
CPP_=fpp -f_com=no -free -w0 $*.F $*$(SUFFIX)

#-----------------------------------------------------------------------
# possible options for CPP:
# NGXhalf charge density reduced in X direction
# wNGXhalf gamma point only reduced in X direction
# avoidalloc avoid ALLOCATE if possible
# PGF90 work around some for some PGF90 / IFC bugs
# CACHE_SIZE 1000 for PII,PIII, 5000 for Athlon, 8000-12000 P4, PD
# RPROMU_DGEMV use DGEMV instead of DGEMM in RPRO (depends on used BLAS)
# RACCMU_DGEMV use DGEMV instead of DGEMM in RACC (depends on used BLAS)
# tbdyn MD package of Tomas Bucko
#-----------------------------------------------------------------------

CPP = $(CPP_) -DHOST=\"LinuxIFC\" \
-DCACHE_SIZE=12000 -DPGF90 -Davoidalloc -DNGXhalf \
# -DRPROMU_DGEMV -DRACCMU_DGEMV

#-----------------------------------------------------------------------
# general fortran flags (there must a trailing blank on this line)
# byterecl is strictly required for ifc, since otherwise
# the WAVECAR file becomes huge
#-----------------------------------------------------------------------

FFLAGS = -FR -names lowercase -assume byterecl

#-----------------------------------------------------------------------
# optimization
# we have tested whether higher optimisation improves performance
# -axK SSE1 optimization, but also generate code executable on all mach.
# xK improves performance somewhat on XP, and a is required in order
# to run the code on older Athlons as well
# -xW SSE2 optimization
# -axW SSE2 optimization, but also generate code executable on all mach.
# -tpp6 P3 optimization
# -tpp7 P4 optimization
#-----------------------------------------------------------------------

# ifc.9.1, ifc.10.1 recommended
OFLAG=-O2 -ip

OFLAG_HIGH = $(OFLAG)
OBJ_HIGH =
OBJ_NOOPT =
DEBUG = -FR -O0
INLINE = $(OFLAG)

#-----------------------------------------------------------------------
# the following lines specify the position of BLAS and LAPACK
# we recommend to use mkl, that is simple and most likely
# fastest in Intel based machines
#-----------------------------------------------------------------------

# mkl path for ifc 11 compiler
#MKL_PATH=$(MKLROOT)/lib/em64t

# mkl path for ifc 12 compiler
MKLROOT=/opt/intel/mkl
MKL_PATH=$(MKLROOT)/lib/intel64

MKL_FFTW_PATH=$(MKLROOT)/interfaces/fftw3xf/

# BLAS
# setting -DRPROMU_DGEMV -DRACCMU_DGEMV in the CPP lines usually speeds up program execution
BLAS= -Wl,--start-group $(MKL_PATH)/libmkl_intel_lp64.a $(MKL_PATH)/libmkl_intel_thread.a $(MKL_PATH)/libmkl_core.a -Wl,--end-group -lpthread -lm #-lguide
# faster linking and available from at least version 11
#BLAS= -lguide -mkl


# LAPACK, use vasp.5.lib/lapack_double

#LAPACK= ../vasp.5.lib/lapack_double.o

# LAPACK from mkl, usually faster and contains scaLAPACK as well

LAPACK= $(MKL_PATH)/libmkl_intel_lp64.a

# here a tricky version, link in libgoto and use mkl as a backup
# also needs a special line for LAPACK
# this is the best thing you can do on AMD based systems !!!!!!

#BLAS = -Wl,--start-group /opt/libs/libgoto/libgoto.so $(MKL_PATH)/libmkl_intel_thread.a $(MKL_PATH)/libmkl_core.a -Wl,--end-group -liomp5
#LAPACK= /opt/libs/libgoto/libgoto.so $(MKL_PATH)/libmkl_intel_lp64.a

#-----------------------------------------------------------------------

LIB = -L../vasp.5.lib -ldmy \
../vasp.5.lib/linpack_double.o $(LAPACK) \
$(BLAS)

# options for linking, nothing is required (usually)
LINK =

#-----------------------------------------------------------------------
# fft libraries:
# VASP.5.2 can use fftw.3.1.X (http://www.fftw.org)
# since this version is faster on P4 machines, we recommend to use it
#-----------------------------------------------------------------------

FFT3D = fft3dfurth.o fft3dlib.o

# alternatively: fftw.3.1.X is slighly faster and should be used if available
#FFT3D = fftw3d.o fft3dlib.o /opt/libs/fftw-3.1.2/lib/libfftw3.a

# you may also try to use the fftw wrapper to mkl (but the path might vary a lot)
# it seems this is best for AMD based systems
#FFT3D = fftw3d.o fft3dlib.o $(MKL_FFTW_PATH)/libfftw3xf_intel.a
#INCS = -I$(MKLROOT)/include/fftw

#=======================================================================
# MPI section, uncomment the following lines until
# general rules and compile lines
# presently we recommend OPENMPI, since it seems to offer better
# performance than lam or mpich
#
# !!! Please do not send me any queries on how to install MPI, I will
# certainly not answer them !!!!
#=======================================================================
#-----------------------------------------------------------------------
# fortran linker for mpi
#-----------------------------------------------------------------------

FC=mpif90
FCL=$(FC)

#-----------------------------------------------------------------------
# additional options for CPP in parallel version (see also above):
# NGZhalf charge density reduced in Z direction
# wNGZhalf gamma point only reduced in Z direction
# scaLAPACK use scaLAPACK (recommended if mkl is available)
# avoidalloc avoid ALLOCATE if possible
# PGF90 work around some for some PGF90 / IFC bugs
# CACHE_SIZE 1000 for PII,PIII, 5000 for Athlon, 8000-12000 P4, PD
# RPROMU_DGEMV use DGEMV instead of DGEMM in RPRO (depends on used BLAS)
# RACCMU_DGEMV use DGEMV instead of DGEMM in RACC (depends on used BLAS)
# tbdyn MD package of Tomas Bucko
#-----------------------------------------------------------------------

#-----------------------------------------------------------------------

CPP = $(CPP_) -DMPI -DHOST=\"LinuxIFC\" -DIFC \
-DCACHE_SIZE=4000 -DPGF90 -Davoidalloc -DNGZhalf \
-DMPI_BLOCK=8000 -Duse_collective -DscaLAPACK -DVASP2WANNIER90
## -DRPROMU_DGEMV -DRACCMU_DGEMV

# "normal version" (parallel) : -DNGZhalf
# gamma-only version (parallel) : -DNGZhalf -DwNGZhalf
# non-collinear version (parallel) : remove both

#-----------------------------------------------------------------------
# location of SCALAPACK
# if you do not use SCALAPACK simply leave this section commented out
#-----------------------------------------------------------------------

# usually simplest link in mkl scaLAPACK
BLACS= -L$(MKL_PATH) -lmkl_blacs_openmpi_lp64
SCA= $(MKL_PATH)/libmkl_scalapack_lp64.a $(BLACS)

#-----------------------------------------------------------------------
# libraries
#-----------------------------------------------------------------------
MKLLIB= $(MKLROOT)/lib/intel64/libmkl_scalapack_lp64.a -Wl,--start-group $(MKLROOT)/lib/intel64/libmkl_intel_lp64.a $(MKLROOT)/lib/intel64/libmkl_core.a $(MKLROOT)/lib/intel64/libmkl_sequential.a -Wl,--end-group $(MKLROOT)/lib/intel64/libmkl_blacs_openmpi_lp64.a -lpthread -lm

LIB = -L../vasp.5.lib -ldmy \
../vasp.5.lib/linpack_double.o \
/home/nm_settings/software/CODES/wannier90/wannier90-1.2/libwannier.a \
$(MKLLIB)
#$(SCA) $(LAPACK) $(BLAS)

#-----------------------------------------------------------------------
# parallel FFT
#-----------------------------------------------------------------------

# FFT: fftmpi.o with fft3dlib of Juergen Furthmueller
FFT3D = fftmpi.o fftmpi_map.o fft3dfurth.o fft3dlib.o

# alternatively: fftw.3.1.X is slighly faster and should be used if available
#FFT3D = fftmpiw.o fftmpi_map.o fftw3d.o fft3dlib.o /opt/libs/fftw-3.1.2/lib/libfftw3.a

# you may also try to use the fftw wrapper to mkl (but the path might vary a lot)
# it seems this is best for AMD based systems
FFT3D = fftmpiw.o fftmpi_map.o fftw3d.o fft3dlib.o $(MKL_FFTW_PATH)/libfftw3xf_intel.a
INCS = -I$(MKLROOT)/include/fftw

#-----------------------------------------------------------------------
# general rules and compile lines
#-----------------------------------------------------------------------
BASIC= symmetry.o symlib.o lattlib.o random.o


SOURCE= base.o mpi.o smart_allocate.o xml.o \
constant.o jacobi.o main_mpi.o scala.o \
asa.o lattice.o poscar.o ini.o mgrid.o xclib.o vdw_nl.o xclib_grad.o \
radial.o pseudo.o gridq.o ebs.o \
mkpoints.o wave.o wave_mpi.o wave_high.o spinsym.o \
$(BASIC) nonl.o nonlr.o nonl_high.o dfast.o choleski2.o \
mix.o hamil.o xcgrad.o xcspin.o potex1.o potex2.o \
constrmag.o cl_shift.o relativistic.o LDApU.o \
paw_base.o metagga.o egrad.o pawsym.o pawfock.o pawlhf.o rhfatm.o hyperfine.o paw.o \
mkpoints_full.o charge.o Lebedev-Laikov.o stockholder.o dipol.o pot.o \
dos.o elf.o tet.o tetweight.o hamil_rot.o \
chain.o dyna.o k-proj.o sphpro.o us.o core_rel.o \
aedens.o wavpre.o wavpre_noio.o broyden.o \
dynbr.o hamil_high.o rmm-diis.o reader.o writer.o tutor.o xml_writer.o \
brent.o stufak.o fileio.o opergrid.o stepver.o \
chgloc.o fast_aug.o fock_multipole.o fock.o mkpoints_change.o sym_grad.o \
mymath.o internals.o npt_dynamics.o dynconstr.o dimer_heyden.o dvvtrajectory.o subdftd3.o \
vdwforcefield.o nmr.o pead.o subrot.o subrot_scf.o paircorrection.o \
force.o pwlhf.o gw_model.o optreal.o steep.o davidson.o david_inner.o \
electron.o rot.o electron_all.o shm.o pardens.o \
optics.o constr_cell_relax.o stm.o finite_diff.o elpol.o \
hamil_lr.o rmm-diis_lr.o subrot_cluster.o subrot_lr.o \
lr_helper.o hamil_lrf.o elinear_response.o ilinear_response.o \
linear_optics.o \
setlocalpp.o wannier.o electron_OEP.o electron_lhf.o twoelectron4o.o \
gauss_quad.o m_unirnk.o minimax_tabs.o minimax.o \
mlwf.o ratpol.o screened_2e.o wave_cacher.o chi_base.o wpot.o \
local_field.o ump2.o ump2kpar.o fcidump.o ump2no.o \
bse_te.o bse.o acfdt.o chi.o sydmat.o \
lcao_bare.o wnpr.o dmft.o \
rmm-diis_mlr.o linear_response_NMR.o wannier_interpol.o linear_response.o auger.o getshmem.o \
dmatrix.o

vasp: $(SOURCE) $(FFT3D) $(INC) main.o
rm -f vasp
$(FCL) -o vasp main.o $(SOURCE) $(FFT3D) $(LIB) $(LINK)
makeparam: $(SOURCE) $(FFT3D) makeparam.o main.F $(INC)
$(FCL) -o makeparam $(LINK) makeparam.o $(SOURCE) $(FFT3D) $(LIB)
zgemmtest: zgemmtest.o base.o random.o $(INC)
$(FCL) -o zgemmtest $(LINK) zgemmtest.o random.o base.o $(LIB)
dgemmtest: dgemmtest.o base.o random.o $(INC)
$(FCL) -o dgemmtest $(LINK) dgemmtest.o random.o base.o $(LIB)
ffttest: base.o smart_allocate.o mpi.o mgrid.o random.o ffttest.o $(FFT3D) $(INC)
$(FCL) -o ffttest $(LINK) ffttest.o mpi.o mgrid.o random.o smart_allocate.o base.o $(FFT3D) $(LIB)
kpoints: $(SOURCE) $(FFT3D) makekpoints.o main.F $(INC)
$(FCL) -o kpoints $(LINK) makekpoints.o $(SOURCE) $(FFT3D) $(LIB)

clean:
-rm -f *.g *.f *.o *.L *.mod ; touch *.F

main.o: main$(SUFFIX)
$(FC) $(FFLAGS)$(DEBUG) $(INCS) -c main$(SUFFIX)
xcgrad.o: xcgrad$(SUFFIX)
$(FC) $(FFLAGS) $(INLINE) $(INCS) -c xcgrad$(SUFFIX)
xcspin.o: xcspin$(SUFFIX)
$(FC) $(FFLAGS) $(INLINE) $(INCS) -c xcspin$(SUFFIX)

makeparam.o: makeparam$(SUFFIX)
$(FC) $(FFLAGS)$(DEBUG) $(INCS) -c makeparam$(SUFFIX)

makeparam$(SUFFIX): makeparam.F main.F
#
# MIND: I do not have a full dependency list for the include
# and MODULES: here are only the minimal basic dependencies
# if one strucuture is changed then touch_dep must be called
# with the corresponding name of the structure
#
base.o: base.inc base.F
mgrid.o: mgrid.inc mgrid.F
constant.o: constant.inc constant.F
lattice.o: lattice.inc lattice.F
setex.o: setexm.inc setex.F
pseudo.o: pseudo.inc pseudo.F
mkpoints.o: mkpoints.inc mkpoints.F
wave.o: wave.F
nonl.o: nonl.inc nonl.F
nonlr.o: nonlr.inc nonlr.F

$(OBJ_HIGH):
$(CPP)
$(FC) $(FFLAGS) $(OFLAG_HIGH) $(INCS) -c $*$(SUFFIX)
$(OBJ_NOOPT):
$(CPP)
$(FC) $(FFLAGS) $(INCS) -c $*$(SUFFIX)

fft3dlib_f77.o: fft3dlib_f77.F
$(CPP)
$(F77) $(FFLAGS_F77) -c $*$(SUFFIX)

.F.o:
$(CPP)
$(FC) $(FFLAGS) $(OFLAG) $(INCS) -c $*$(SUFFIX)
.F$(SUFFIX):
$(CPP)
$(SUFFIX).o:
$(FC) $(FFLAGS) $(OFLAG) $(INCS) -c $*$(SUFFIX)

# special rules
#-----------------------------------------------------------------------
# these special rules have been tested for ifc.11 and ifc.12 only

fft3dlib.o : fft3dlib.F
$(CPP)
$(FC) -FR -lowercase -O2 -c $*$(SUFFIX)
fft3dfurth.o : fft3dfurth.F
$(CPP)
$(FC) -FR -lowercase -O1 -c $*$(SUFFIX)
fftw3d.o : fftw3d.F
$(CPP)
$(FC) -FR -lowercase -O1 $(INCS) -c $*$(SUFFIX)
fftmpi.o : fftmpi.F
$(CPP)
$(FC) -FR -lowercase -O1 -c $*$(SUFFIX)
fftmpiw.o : fftmpiw.F
$(CPP)
$(FC) -FR -lowercase -O1 $(INCS) -c $*$(SUFFIX)
wave_high.o : wave_high.F
$(CPP)
$(FC) -FR -lowercase -O1 -c $*$(SUFFIX)
# the following rules are probably no longer required (-O3 seems to work)
wave.o : wave.F
$(CPP)
$(FC) -FR -lowercase -O2 -c $*$(SUFFIX)
paw.o : paw.F
$(CPP)
$(FC) -FR -lowercase -O1 -c $*$(SUFFIX)
cl_shift.o : cl_shift.F
$(CPP)
$(FC) -FR -lowercase -O2 -c $*$(SUFFIX)
us.o : us.F
$(CPP)
$(FC) -FR -lowercase -O1 -c $*$(SUFFIX)
LDApU.o : LDApU.F
$(CPP)
$(FC) -FR -lowercase -O2 -c $*$(SUFFIX)
# added from website hint, 2014-11-03
davidson.o : davidson.F
$(CPP)
$(FC) $(FFLAGS) -O1 -c $*$(SUFFIX)
[root@manager vasp.5.3]#